Not all safety seats can be installed in all types of vehicles or seating positions. With numerous models of child safety seats, more than 300 models of passenger vehicles and the wide range of belt systems available today, correctly installing a child safety seat can be challenging. The best way to be sure your safety seat is compatible with the vehicle you are considering is to test it -- before you purchase or lease the vehicle.
Safety first: To correctly install a child safety seat, place your knee into the seat and lean forward while tightening the belt.
Be sure to read the child safety seat's instruction manual and review all information in the vehicle owner's manual concerning correct installation.
Once the safety seat is installed, check it by firmly pulling the base of the seat from side to side and forward. The seat should not move more than one inch in any direction.
Other Factors to Consider
- Two-door vehicles: It can be
difficult to install child safety seats correctly because you must get into
the back seat yourself. It also can be difficult to get your child in and
out of the safety seat.
- Small back seats: The back
seats of small cars and many pickup trucks are too small to properly
accommodate some safety seats, especially those in the rear-facing reclined
position. In addition, some rear center safety belts in small cars are too
close together to fit safety seats with wide bases. Wide bases may block
access to buckles for outboard lap and shoulder belts. In this case, try a
safety seat with a narrow base.
- Deep bucket seats: Many
safety seats will not fit in vehicle seats with deep buckets. Try a safety
seat with a narrow base or top tether strap.
- Tether anchorage: This is a
metal plate bolted into the vehicle to attach a top-tether strap that comes
with some child safety seats. Tethers may improve protection by attaching
the top of the safety seat more securely to the vehicle. Virtually all
passenger cars made since January 1989 have pre-drilled holes that can be
used for top-tether anchorage.
- Slope of back seat:
Rear-facing infant and convertible seats should be reclined at a 45 degree
angle. The slope of the seat may cause the safety seat to tilt too far
forward, putting the infant in an upright rather than reclined position. To
remedy this situation, try placing a tightly rolled towel under the base of
the safety seat. Always check the safety seat instructions and owner's
manual for correct installation.
Getting the best angle: Placing a tightly rolled towel under the base of a child safety seat may help achieve the correct 45 degree angle.
- Contour of back seat: While
the rear center seat may seem the safest place to put a child, many back
seats have a hump in the center, making it difficult to install a child
safety seat correctly. The safest position is where the safety seat fits
securely.
- Split bench seats: Splits in
wide bench seats can make it difficult to install a safety seat correctly.
- Forward-anchored belts: If
the safety belt extends from the seat forward of where the back and seat
cushions meet, the safety seat may be too loose. Move it to a different
seating position, or try a different style safety seat, perhaps one that can
accommodate a top-tether strap.
- Pickup truck jumpseats/extended cabs:
Child safety seats will not fit properly in many pickup truck rear seats.
There is not enough space between the rear of the front seat and the child
to allow forward motion in the event of a crash or even a sudden stop.
Side-facing jumpseats are not safe for a child safety seat under any
circumstances.
Vehicles manufactured before Sept. 1, 1995
Some vehicles may have safety belt systems — such as automatic safety belts — that require additional hardware to install child safety seats correctly. Be sure to read both the vehicle and safety seat manuals and labels on safety belts.
Vehicles manufactured after Sept. 1, 1995
Vehicles now are equipped with safety belt locking features — such as locking or switchable retractors — that make installation of child safety seats easier. To be sure, read the vehicle owner’s manual and safety belt labels.
Beware: Danger Areas for Children
Kids Are Not Cargo!
Never let children ride or play in the cargo area, trunk or bed of any vehicle -- even if the area is covered. They can be thrown from the vehicle in the event of a crash, sudden stop or even rough road.
Trunks
Make sure children do not have access to your vehicle's trunk. Once inside, they may not be able to escape, even if they entered through the interior, since many rear seats only release to the trunk from inside the passenger compartment. Children trapped in trunks can die of suffocation or heat stroke.
Unattended Children
Never allow children unmonitored access to vehicles or leave them unattended in a vehicle. When left in a vehicle, children can quickly become ill or die from heat build-up inside of the vehicle. In addition, never allow children access to car keys or remote locking/unlocking devices. A child could put the vehicle in gear or neutral so it rolls away.
Keep children safe by keeping them out of your vehicle unless you are there!
